Add Listing

WOBANE Motion Activated LED Strip Light, Rechargea…

  • March 17, 2025
  • (7)
Sale!
motion activated lighting fixtures
WOBANE Motion Activated LED Strip Light, Rechargea... - Image 2
WOBANE Motion Activated LED Strip Light, Rechargea... - Image 3
WOBANE Motion Activated LED Strip Light, Rechargea... - Image 4
WOBANE Motion Activated LED Strip Light, Rechargea... - Image 5
WOBANE Motion Activated LED Strip Light, Rechargea... - Image 6
WOBANE Motion Activated LED Strip Light, Rechargea... - Image 7

Original price was: 29 $.Current price is: 16 $.

Product Description

The video showcases the product in use.The video guides you through product setup.The video compares multiple products.The video shows the product being unpacked.

motion sensor stair lights Motion Sensor+Light Sensor

Auto on Motion detected in dark within 10ft;Auto off in bright;Auto off after 20s of inactivity

led sensor light

Every 3 leds has a cuttable mark

battery led light

Each strip bar has 60 LEDs, provide MAX 200 lumen when fully charged

1 Motion Sensor

2 Cuttable

3 Super Bright

motion sensor closet lights Battery Powered LED Strip Lights bookcase lights motion sensor led lights gun safe lights

1 Closet 2 Wine Cabinet 3 Bookcase 4 Pantry 5 Gun safe lights

USB RechargeableUSB Rechargeable USB Rechargeable

Equipped with 2200mAH large rechargeable battery, keep the lights on without the need of a wall outlet or electrician. Convenient and practical.

Wireless led strip LightWireless led strip Light Easy to Install

No tools, screws or nuts needed. These PIR light strip can be installed in seconds. Stick on anywhere you want with the backed adhesive tape

tent lightingtent lighting Portable application

It can also be used as temporary lighting, such as in tents, RVs, etc. When it is portable, do not tear off the adhesive tape, easy to carry.

bed lightingbed lighting Bedroom application

Perfect for bedroom, such as bedside lamp, night lamp. or a safety light when your kid gets up at night.

WOBANE Sensor Light Strips

Add to Cart

Add to Cart

Customer Reviews

4.2 out of 5 stars 2,949

4.7 out of 5 stars 114

4.4 out of 5 stars 3,002

4.4 out of 5 stars 280

4.3 out of 5 stars 827

4.3 out of 5 stars 1,623

Price

$21.59$21.59

$29.99$29.99

$17.99$17.99

$35.99$35.99

$14.44$14.44

$29.99$29.99

Color

Warm White

18 Colors

Warm White

5 Colors

Warm White

Warm White

Size

2*6.56ft

2pack

16.4ft

24inch

12inch

3pack

Number of LEDs

2*60

56*2

300

112

30

24

Control method

Button+motion sensor

Button+motion sensor+IR remote

Remote+motion sensor

Hand wave

Hand wave

Button+motion sensor

Power Source

Rechargeable

Rechargeable

Adpter

Adpter

Adpter

Rechargeable

Dimmable

✘

✔

✔

✔

✔

✘

Product Dimensions ‏ : ‎ 3.94 x 1.18 x 3.94 inches; 5.29 ounces
Batteries ‏ : ‎ 1 Lithium Polymer batteries required. (included)
Date First Available ‏ : ‎ August 19, 2021
Manufacturer ‏ : ‎ Shenzhen Wobane Trading Co.,Ltd
ASIN ‏ : ‎ B09D2GD291
Country of Origin ‏ : ‎ China

Automatic LED Cabinet Light:Built-in motion sensor and night sensor, auto-on with 10 feet when it detects the motion of human in the dark,auto-off after 20 seconds of no movement or placed in a bright environment
USB rechargeable Control Box:It is built-in 2200 mAH chargeable battery and magnetics.The strong magnet adsorption method prevents the control box from falling,and is also convenient for installation and remove to charge
Super Bright LED Strip Lights:Total 60 LEDs supports MAX 200 lumen,high quality LED glow,2700 K cozy light glow,Ra>80
Easy to Install:No tools,screws or nuts needed.These PIR light strip can be installed in seconds.Stick on anywhere you want with the backed adhesive tape
Widely Application:This cordless LED light strip is ideal for stairway,shelf,stairs,tent,bookshelf,baby room, bedroom,kitchen,garage,attic,basement,closet,corridor,entrances,outages,pantry,trunk ETC
Tips:If you need the light to be able to motion sense even in a bright environment,you can cover the light sensor with a small black tape

Category:

Description

Price: $28.96 - $15.99
(as of Mar 17, 2025 09:10:16 UTC – Details)


Product Description

…

Customers say

Customers find the string lights effective and reliable. They appreciate the bright illumination and simple installation process. The lights are easy to charge and maintain without a charge. However, some customers have experienced issues with battery life and motion sensor functionality.

AI-generated from the text of customer reviews

Related products

7 Comments

  • A K

    1 month ago / March 17, 2025 @ 9:10 am
    Reply

    Works very well! Easy to install
    I like this LED light string product. It works well, very responsive motion detection and light detection. The light is so bright, I don’t need to turn on the ceiling light to be able to see my way up/down the stairs. It has sensors at the top of the stairs and at the bottom. The sensor boxes have two settings: M or A.M means Manual mode. With Manual mode, you have to manually press an on/off switch on the sensor box to turn the lights on or off. The lights stay on until you turn them off, no motion or light sensing. This mode runs down the battery faster, so it will need recharging more frequently if you use Manual mode. A means Automatic mode, which is the light and motion sensor mode. The lights turn off automatically after about 30 seconds of no motion detected. This mode is more battery saving.I bought the 16.4 foot long light string, after measuring my stairway. It has two sensor boxes (which sense both motion and light level), which you attach to the wall with magnetic strips. It’s easy to unplug the sensor box and pull it off the magnetic strips to recharge it with a standard Android cable. Something that was not clear from the description of the product is that there is (for the 16.4 foot long model) one light string and each end of the string has a sensor box.The one con is that the instructions that come with it are VERY lacking. There are some parts that come with it and the instructions don’t explain at all about these parts and what they are for. I had to figure it out on my own.So, I will try my best to explain the parts to you. There are some little circular stickers. These stickers are for covering the light sensor pinhole to convert the sensor box into a motion detector only, so that it only detects motion without regard to light levels. This means it will always trigger from motion no matter what time of day it is and how much light is coming in.There are 2 cable clips to attach the bit of cable that comes from the sensor box to the wall.There are 2 sets of wires that are red and black and have plastic bits at the ends. This one took me a while to figure out. It turns out to be a connector piece. The LED light strip has little black lines at intervals along the strip. These black lines mark where it is safe to cut the strip to make it shorter, without ruining the conductivity of electricity through the strip, so that it will still light up after being cut shorter. You cut exactly on the black line with your scissors. I did not need to cut my light strip, it was left intact, so I did not need to use these connectors. The connectors are for reconnecting the two parts of the light strip if you change your mind and want to reunite the cut sections. The way it works is you pry open the plastic clamps at the ends of the connector wires – this can be difficult to do, but I managed to do it with my fingernail. I suggest using a small flathead screwdriver instead of your fingernail, it’s easier that way. Then after you’ve got it pried open, you lay the cut end of the light strip in it and then close the clamp over the cut end. Do the same for the other side of the connector, and then you’ve got the LED strips reunited and working as a single piece again.I hope this review helps you make a decision about whether this product is right for your needs. I highly recommend it.

  • N. Hosein

    1 month ago / March 17, 2025 @ 9:10 am
    Reply

    Basic Motion Activated Stairlights
    I purchased this solution as my house is old (built in 1905) and the stairs are dark. I’ve had guests trip going up and down the stairs so I figured why not light the path for safety. I will break down the review into three parts, motion detection, brightness and installation.Motion DetectionAccording to the instructions, the sensor has a range of 7-10 ft. It’s sensitivity is appropriate from proximity as when I get by the stairs, it lights up. The operation is instant on with no pattern and after no motion is detected for 25 seconds it shuts off. One thing to note is when turning off the lights in my foyer, the lights automatically turn on. I don’t know if it matters to anyone but I find it helpful as I don’t have to get near the sensor in the dark for it to activate. One thing to note is since both ends pass power, when both sensors are tripped, the lights get even brighter.I charged the sensors out of the box and it took a long time to complete charging (the instructions state 2-4 hours). I heard some people had issues with the battery packs not holding a charge after a while so I will update my review after a month to give my experience.BrightnessThe package states it has an output of 220 lumens. As I do not have a means to confirm this, I take it for face value. The strip produces enough light to illuminate the stairs in the dark and in ambient lighting. However, I would prefer it if the strip was a bit brighter for my own personal taste. Further, I feel the LEDs are a bit too spread out and feel it would benefit with a closer set of LEDs or double the LEDs.Note: I chose the 6000k color temperature as I felt it suited my needs.InstallationAs with any project, one must start with prep work by cleaning the surface for the lights to adhere. As this is my house, I went the extra mile. I swept and steamed the stairs from top to bottom. For the area where I adhered the lights, I hit it with a dry wipe then used lysol wipes and let it dry.As I have a landing, I employed the use of another person to hold the lights so I can stretch it out to see both ends and get an idea of placement. Then I peeled the backing of the iron sheets and placed the sensor on the lower part of the stairs. I plugged it up and started peeling the backing off and affixed the LED strip to the staircase (disconnecting once I got the initial part of the strip adhered). When I got to the landing I had to come around so I cut the strip and tethered it with the included connectors. I secured the cord and continued to the last part at the top of the stairs. Once the entire strip was installed, I mounteded the second sensor and the task was complete.I say the installation was fairly easy that an inexperienced individual could attempt it and be successful and the time it took to complete from start to finish was about 30 minutes where most of the time was dedicated to prep work. Adhering the LEDs was the easiest part while the wire connector part (unnecessary in some cases) took a little time to work with as I had accidentally peeled the backing in the area that was going to be connected. It just made things more difficult because the sticky part kept sticking to my fingers or the connector in the wrong area.Final ThoughtsI recommend purchasing these lights as I believe they provide great value for the cost. Unless you’re willing to go all out for an illumination solution for your stairs, this simple solution works great! The ability to have the lights powered by battery provides the freedom to mount the solution virtually anywhere.I took as many pictures as I could for an idea of what to expect.

  • Aziz

    1 month ago / March 17, 2025 @ 9:10 am
    Reply

    حطيتها تحت السرير.. وجدا رائعة .. الحساس ممتاز وسريع الاستجابة,

  • Raul Perez

    1 month ago / March 17, 2025 @ 9:10 am
    Reply

    Está muy bien para un clóset o armario, se puede prender de forma manual o en automático al estar oscuro detecta movimiento y prende 20 segundos.

  • Eleanor Thomas

    1 month ago / March 17, 2025 @ 9:10 am
    Reply

    It is really great, we have it set to automatic mode on the underside of the handrail in the stairs. The motion sensor is very receptive. It doesn’t come on in daylight. We can switch it to manual mode if need be. These stairs go up to second floor where the bedrooms are, so not super high traffic area. The lights have been installed for three weeks and I haven’t had to charge them yet (except for pre-installation). It was very easy to install. The luminosity is fantastic, the stairwell is well lit up but not too blinding for the eyes. Very good purchase, I will be buying more. The charging doesn’t take very long, 3 hours maybe.

  • La Paz

    1 month ago / March 17, 2025 @ 9:10 am
    Reply

    Facilidad para instalar

  • John in Markham ON

    1 month ago / March 17, 2025 @ 9:10 am
    Reply

    We are using them temporarily without the adhesive strip. We are not done with our renovation project and will varnish the railing next year. We do not want to spoil it by removing it. So I can’t comment on how well it sticks. I can however say the the product is perfect for our application. It is very bright and the sensor pics our motion very well when going from the bottom or from the top of our stairs. The battery seems to hold the charge well but it has been only a few weeks so we will see how long it last before needing recharging. We are very happy with our choice so far.

Leave a Comment

Leave a Reply

Your email address will not be published. Required fields are marked *

Verified by MonsterInsights